How to Install Kohler Bevin Pull-Down Kitchen Faucet?

What is the Kohler Bevin Pull-Down Kitchen Faucet?

The Kohler Bevin K-R43210 is a modern pull-down kitchen faucet designed for superior functionality. It features:

• Two-function sprayhead: Switch between aerated stream and Sweep® spray.
• ProMotion® technology: A light, quiet braided hose for smooth retraction.
• DockNetik® secure docking: Locks the sprayhead into place.
• MasterClean™ sprayface: Resists mineral buildup for easy cleaning.
• High-arch swivel spout: Provides ample space for washing large pots and dishes.
• ADA-compliant single lever handle: Ensures smooth water control.
• 1.5 GPM flow rate: Ensures efficient water usage.

This guide shows you how to install the Kohler Bevin Pull-Down Kitchen Faucet easily.

Tools & Materials Needed

Before you begin, gather these tools and materials:

• Adjustable wrench
• Phillips screwdriver
• Plumber’s tape
• Basin wrench
• Bucket (to catch excess water)
• Silicone sealant (for a watertight fit)
• Towel (to clean any spills)

Step-by-Step Installation Guide

Step 1: Turn Off the Water Supply

• Locate the shut-off valves under your sink.
• Turn the valves clockwise to shut off the water.
• Open the faucet to drain any remaining water.
• Place a bucket under the pipes to catch excess water.

Step 2: Remove the Old Faucet

• Disconnect the water supply lines using an adjustable wrench.
• Loosen the mounting nuts securing the old faucet.
• Gently lift the old faucet out of the sinkhole.
• Clean the area to remove old sealant and debris.

Step 3: Install the New Faucet Base

• If using a 3-hole sink, attach the escutcheon plate.
• Insert the faucet through the sinkhole.
• From underneath, secure the faucet using the provided mounting hardware.
• Tighten the mounting nuts to ensure a secure fit.

Step 4: Connect the Supply Lines

• Attach the hot and cold water supply lines to the shut-off valves.
• Use plumber’s tape to prevent leaks.
• Tighten the connections with an adjustable wrench.

Step 5: Install the Sprayhead & DockNetik® System

• Attach the sprayhead hose to the faucet body.
• Secure the DockNetik® magnetic docking system.
• Ensure smooth pull-down and retraction of the sprayhead.

Step 6: Turn On Water & Check for Leaks

• Slowly turn the shut-off valves counterclockwise.
• Turn on the faucet and check for any leaks.
• Run water for a few minutes to flush out debris.

Troubleshooting Common Issues

1. Faucet Leaks After Installation

• Check if the supply line connections are tight.
• Apply plumber’s tape to any leaking joints.
• Ensure the mounting nuts are secure.

2. Sprayhead Not Docking Properly

• Adjust the DockNetik® system to improve magnetic docking.
• Ensure the hose moves freely without obstructions.

3. Low Water Pressure

• Check for clogs in the aerator and clean if necessary.
• Ensure the shut-off valves are fully open.

Frequently Asked Questions (FAQs)

How long does it take to install the Kohler Bevin faucet?

Installation takes approximately 30-60 minutes depending on experience.

Do I need a plumber to install this faucet?

No, the installation is DIY-friendly with basic tools.

Can I install the Kohler Bevin faucet on a 3-hole sink?

Yes, use the included escutcheon plate for 3-hole installations.

What is the flow rate of the Kohler Bevin faucet?

The faucet has a 1.5 GPM (5.7 LPM) flow rate, ensuring water efficiency.

Is the Kohler Bevin faucet ADA-compliant?

Yes, the lever handle meets ADA accessibility standards.

Conclusion

Installing the Kohler Bevin Pull-Down Kitchen Faucet is a simple process with basic tools and proper guidance. Follow this simple installation guide to enjoy a stylish, high-performance faucet—no need for a plumber!